Skip to main content

Building a Hybrid Yugoslav M70B1 from a Stub with Screws

Building a Hybrid Yugoslav M70B1 from a Stub with Screws

George Spafford is building a replica of the Yugo M70B rifle using a stub parts kit. A new installment will appear here every Friday

Install the Barrel — Part 1

Here, an AK-Builder barrel press jig holds the trunnion in proper alignment as Spafford uses his 20-ton press to push the barrel back into place. It's critical to have the barrel straight, not only to avoid canted sights but also any potential binding problems that could cause the barrel to bend. Take your time, and if it feels like too much pressure is being required, stop and carefully inspect everything in case something shifted and is misaligned.

Next up is the reinsertion of the barrel. I put the barrel in the freezer for a few hours so it can shrink. When ready to install it, I insert the receiver and trunnion assembly in a vise and first polish the inside of the trunnion with emery cloth to remove any burrs. You want to remove as little material as possible. I then warm the trunnion with a heat gun so it will expand and apply a light coat of Permatex non-seize coating to help the parts slide together.

At this point, I get the barrel from the freezer, run out to my shop, align the barrel to the front trunnion by sighting down the "ears" of the trunnion and lining up the rear sight block (RSB) on the barrel, and then press the parts together by hand. I quickly double-check the alignment and give a few whacks with a mallet on the protected muzzle end to seat the barrel further.

To be clear, I use a beat up old muzzle brake that I cut flat on the end. Some guys have very good luck using a old blank firing adapter for the same purpose. Regardless of the method, you want to protect the muzzle from damage.

After this initial start, I take the receiver and barrel assembly to the press to finish the job using an AK-Builder barrel jig. There are a number of other proven methods including using a mallet for the whole job, air riveters, threaded rod and other press jigs.

As you get close to the original pin location, take it nice and slow. Clean out the channel with a Q-tip or pipe cleaner so you can clearly see how the parts are coming together. Trust me, it is much easier to press the barrel in than to try and press it back out — especially if you don't have the tools to do so.

Take your time and make sure the barrel channel lines up. This will be the starting point for checking headspacing. With a worn M70, you probably will need to adjust the headspace and use an oversize pin — George did and that will be discussed in the next installment.

Recommended





GET THE NEWSLETTER Join the List and Never Miss a Thing.

Recommended Articles

Recent Videos

KelTec releases their PR57 pistol and SUB2000 rifle in 5.7x28mm as the demand grows for more firearms in this unique and...
Gear

Firearms News Gets the Rundown on Burris's New XTR-PS

KelTec releases their PR57 pistol and SUB2000 rifle in 5.7x28mm as the demand grows for more firearms in this unique and...
Guns

SDS Arms Releases New Tactical Shotgun Lineup

KelTec releases their PR57 pistol and SUB2000 rifle in 5.7x28mm as the demand grows for more firearms in this unique and...
Guns

New Hunting Shotguns Available in Mossy Oak and Realtree Camo

KelTec releases their PR57 pistol and SUB2000 rifle in 5.7x28mm as the demand grows for more firearms in this unique and...
Guns

Inglis MFG Launches New P35 Pistol

KelTec releases their PR57 pistol and SUB2000 rifle in 5.7x28mm as the demand grows for more firearms in this unique and...
Guns

MAC Firearms unveils New 5' Comp Barreled Double Stack 1911

KelTec releases their PR57 pistol and SUB2000 rifle in 5.7x28mm as the demand grows for more firearms in this unique and...
Gear

New Iron Lady Gun Safes from ATI

KelTec releases their PR57 pistol and SUB2000 rifle in 5.7x28mm as the demand grows for more firearms in this unique and...
Guns

American Tactical Releases GSG Anniversary 1911 Pistol

KelTec releases their PR57 pistol and SUB2000 rifle in 5.7x28mm as the demand grows for more firearms in this unique and...
Gear

First Look at ATI's new Rukx Rifle Case

KelTec releases their PR57 pistol and SUB2000 rifle in 5.7x28mm as the demand grows for more firearms in this unique and...
Guns

ATI Launches New Double and Triple Barreled Shotguns for 2025

KelTec releases their PR57 pistol and SUB2000 rifle in 5.7x28mm as the demand grows for more firearms in this unique and...
Guns

American Tactical Showcases their Latest GSG-16 22 LR Pistol and 410 Bull Dog Shotgun

KelTec releases their PR57 pistol and SUB2000 rifle in 5.7x28mm as the demand grows for more firearms in this unique and...
Gear

New Glock 17/19 18-Round Magazines Offered by Mec-Gar

KelTec releases their PR57 pistol and SUB2000 rifle in 5.7x28mm as the demand grows for more firearms in this unique and...
Guns

KelTec Launches PR57 Pistol: The Best and Lightest 5.7

Firearms News Magazine Covers Print and Tablet Versions

GET THE MAGAZINE Subscribe & Save

Digital Now Included!

SUBSCRIBE NOW

Give a Gift   |   Subscriber Services

PREVIEW OUR CURRENT ISSUE

Buy Digital Single Issues

Magazine App Logo

Don't miss an issue.
Buy single digital issue for your phone or tablet.

Get the Firearms News App apple store google play store

Other Magazines

See All Other Magazines

Special Interest Magazines

See All Special Interest Magazines

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Get the top Firearms News stories delivered right to your inbox.

Phone Icon

Get Digital Access.

All Firearms News subscribers now have digital access to their magazine content. This means you have the option to read your magazine on most popular phones and tablets.

To get started, click the link below to visit mymagnow.com and learn how to access your digital magazine.

Get Digital Access

Not a Subscriber?
Subscribe Now

Enjoying What You're Reading?

Get a Full Year
of Guns & Ammo
& Digital Access.

Offer only for new subscribers.

Subscribe Now

Never Miss a Thing.

Get the Newsletter

Get the top Firearms News stories delivered right to your inbox.

By signing up, I acknowledge that my email address is valid, and have read and accept the Terms of Use